Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-3: Particular requirements for hand-held grinders, disc-type polishers and disc-type sanders

EN-IEC 62841-2-3 applies to hand-held grinders, disc-type polishers and disc-typesanders, including angle, straight and vertical tools, intended for use on various materials except magnesium, with a rated capacity not exceeding 230 mm. For grinders, the rated no load speed does not exceed a peripheral speed of the accessory of 80 m/s at rated capacity.This standard does not apply to dedicated cut-off machines. This standard does not apply to orbital polishers and orbital sanders.

Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 2-3: Besondere Anforderungen für handgeführte Schleifer, Polierer mit Polierscheibe und Schleifer mit Schleifblatt

Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 2-3: Exigences particulières pour les meuleuses portatives et pour les lustreuses et ponceuses portatives du type à disque

IEC 62841-2-3:2020 s'applique aux meuleuses portatives, aux lustreuses portatives du type à disque et aux ponceuses portatives du type à disque, y compris dans leur version d'angle, droite ou verticale, prévues pour une utilisation sur divers matériaux à l'exception du magnésium, et dont la capacité assignée ne dépasse pas 230 mm. Pour les meuleuses, la vitesse assignée à vide ne dépasse pas une vitesse périphérique de l'accessoire de 80 m/s à la capacité assignée.
La présente norme ne s'applique pas aux tronçonneuses dédiées.
La présente norme ne s'applique pas aux lustreuses orbitales ni aux ponceuses orbitales.
La présente norme ne s'applique pas aux meules à rectifier les matrices.
L'attention des Comités nationaux est attirée sur le fait que les fabricants d'appareils et les organismes d'essai peuvent avoir besoin d'une période transitoire après la publication d'une nouvelle publication IEC, ou d'une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés.
Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 36 mois après la date de publication.

Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-3. del: Posebne zahteve za ročne brusilnike, diskovne polirnike in diskovne brusilnike

General Information

Status
Published
Publication Date
14-Jun-2021
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
04-Jun-2021
Due Date
09-Aug-2021
Completion Date
15-Jun-2021

Relations

Buy Standard

Standard
EN IEC 62841-2-3:2021
English language
70 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 62841-2-3:2021
01-julij-2021
Nadomešča:
SIST EN 60745-2-3:2011
SIST EN 60745-2-3:2011/A11:2014
SIST EN 60745-2-3:2011/A12:2015
SIST EN 60745-2-3:2011/A13:2016
SIST EN 60745-2-3:2011/A2:2014
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-
3. del: Posebne zahteve za ročne brusilnike, diskovne polirnike in diskovne
brusilnike
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 2-3: Particular requirements for hand-held grinders, disc-type
polishers and disc-type sanders
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen - Sicherheit - Teil 2-3: Besondere Anforderungen für
handgeführte Schleifer, Polierer mit Polierscheibe und Schleifer mit Schleifblatt
Ta slovenski standard je istoveten z: EN IEC 62841-2-3:2021
ICS:
25.080.50 Brusilni in polirni stroji Grinding and polishing
machines
25.140.20 Električna orodja Electric tools
SIST EN IEC 62841-2-3:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 62841-2-3:2021

---------------------- Page: 2 ----------------------
SIST EN IEC 62841-2-3:2021


EUROPEAN STANDARD EN IEC 62841-2-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2021
ICS 25.140.20 Supersedes EN 60745-2-3:2011 and all of its
amendments and corrigenda (if any)
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 2-3: Particular
requirements for hand-held grinders, disc-type polishers and
disc-type sanders
(IEC 62841-2-3:2020)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 2-3: Exigences transportable Werkzeuge und Rasen- und
particulières pour les meuleuses portatives et pour les Gartenmaschinen - Sicherheit - Teil 2-3: Besondere
lustreuses et ponceuses portatives du type à disque Anforderungen für handgeführte Schleifer, Polierer mit
(IEC 62841-2-3:2020) Polierscheibe und Schleifer mit Schleifblatt
(IEC 62841-2-3:2020)
This European Standard was approved by CENELEC on 2020-05-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 62841-2-3:2021 E

---------------------- Page: 3 ----------------------
SIST EN IEC 62841-2-3:2021
EN IEC 62841-2-3:2021 (E)
European foreword
The text of document 116/444/FDIS, future edition 1 of IEC 62841-2-3, prepared by IEC/TC 116
"Safety of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 62841-2-3:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-05-03
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-05-03
document have to be withdrawn
This document supersedes EN 60745-2-3:2011 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of
EN IEC 62841-2-3:2021/A11:2021.
Endorsement notice
The text of the International Standard IEC 62841-2-3:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60086-1 NOTE Harmonized as EN 60086-1
IEC 61010-031 NOTE Harmonized as EN 61010-031
IEC 61439-1 NOTE Harmonized as EN 61439-1
IEC 62368-1 NOTE Harmonized as EN IEC 62368-1
ISO 13857:2019 NOTE Harmonized as EN ISO 13857:2019 (not modified)


2

---------------------- Page: 4 ----------------------
SIST EN IEC 62841-2-3:2021



IEC 62841-2-3

®


Edition 1.0 2020-04




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Electric motor-operated hand-held tools, transportable tools and lawn and

garden machinery – Safety –

Part 2-3: Particular requirements for hand-held grinders, disc-type polishers and


disc-type sanders



Outils électroportatifs à moteur, outils portables et machines pour jardins et


pelouses – Sécurité –

Partie 2-3: Exigences particulières pour les meuleuses portatives et pour les

lustreuses et ponceuses portatives du type à disque










INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 25.140.20 ISBN 978-2-8322-8100-0




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 5 ----------------------
SIST EN IEC 62841-2-3:2021
– 2 – IEC 62841-2-3:2020 © IEC 2020
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 General requirements . 10
5 General conditions for the tests . 11
6 Radiation, toxicity and similar hazards . 11
7 Classification . 11
8 Marking and instructions . 11
9 Protection against access to live parts . 18
10 Starting . 18
11 Input and current . 18
12 Heating . 18
13 Resistance to heat and fire . 18
14 Moisture resistance . 18
15 Resistance to rusting . 18
16 Overload protection of transformers and associated circuits . 19
17 Endurance . 19
18 Abnormal operation . 19
19 Mechanical hazards . 19
20 Mechanical strength . 27
21 Construction . 37
22 Internal wiring . 41
23 Components . 41
24 Supply connection and external flexible cords . 41
25 Terminals for external conductors . 41
26 Provision for earthing . 41
27 Screws and connections . 41
28 Creepage distances, clearances and distances through insulation . 41
Annexes . 42
Annex I (informative) Measurement of noise and vibration emissions . 42
Annex K (normative) Battery tools and battery packs . 51
Annex L (normative) Battery tools and battery packs provided with mains connection
or non-isolated sources . 54
Annex AA (normative) Wheel guard types . 55
Annex BB (informative) Material and thickness of wheel guards . 61
Annex CC (normative) Wheel type specifications . 62
Bibliography . 68

Figure 101 – Example of an angle grinder . 9
Figure 102 – Example of a straight grinder . 9
Figure 103 – Example of a vertical grinder . 10

---------------------- Page: 6 ----------------------
SIST EN IEC 62841-2-3:2021
IEC 62841-2-3:2020 © IEC 2020 – 3 –
Figure 104 – Examples of gaps and rake angles . 17
Figure 105 – Principal dimensions of flanges for wheels other than Type 4 . 24
Figure 106 – Principal dimensions of flanges for wheels type 4 . 24
Figure Z101 – Depressed centre of abrasive wheels . 25
Figure 107 – Wheel guard strength test: explanation of wheel guard positions . 29
Figure 108 – Wheel guard strength test: preparation of the grinder . 30
Figure 109 – Wheel guard strength test: preparation of cup wheel types 6 and 11 . 31
Figure 110 – Wheel guard strength test: angle grinders and vertical grinders without
side handles . 32
Figure 111 – Wheel guard strength test box . 33
Figure 112 – Wheel guard strength test: straight grinder with additional masses . 37
Figure 113 – Measurement of handle gripping length . 39
Figure 114 – Measurement of handle gripping length . 40
Figure 115 – Measurement of handle gripping length for a handle with finger grips or
similar superimposed profiles . 40
Figure I.101 – Positions of transducers for straight grinders . 42
Figure I.102 – Positions of transducers for angle grinders . 43
Figure I.103 – Positions of transducers for disc-type polishers and disc-type sanders . 43
Figure I.104 – Artificial grinding wheel for angle grinding and concrete grinding . 45
Figure I.105 – Working positions of operator and application of force . 46
Figure I.106 – Artificial grinding wheel for straight grinding . 48
Figure AA.1 – Design example for wheel guard of Type A (cut-off wheel guard) . 55
Figure AA.2 – Wheel guard of Type B (grinding wheel guard) . 56
Figure AA.3 – Wheel guard of Type C (combination wheel guard) . 57
Figure AA.4 – Adjustable wheel guard of Type D (cup wheel guard) . 57
Figure AA.5 – Wheel guard of Type E (diamond surface grinding wheel guard) . 58
Figure AA.6 – Wheel guard of Type F (masonry cut-off wheel guard) . 59
Figure AA.7 – Wheel guard of Type G (straight grinder wheel guard) . 60
Figure CC.1 – Wheel type 1 . 62
Figure CC.2 – Wheel type 4 . 63
Figure CC.3 – Wheel type 6 . 63
Figure CC.4 – Wheel type 11 . 64
Figure CC.5 – Wheel type 27 . 65
Figure CC.6 – Wheel type 28 . 65
Figure CC.7 – Wheel type 29 . 66
Figure CC.8 – Wheel type 41 . 66
Figure CC.9 – Wheel type 42 . 67

Table 4 – Required performance levels . 19
Table 101 – Accessories and guards for various applications . 22
Table Z101 – Dimensions of depressed centre wheels . 25
Table 102 – Minimum flange dimensions for wheel type 4 . 26
Table 103 – Torques for testing flanges . 26
Table 104 – Typical pre-cut length ranges for standard wheel dimensions . 31

---------------------- Page: 7 ----------------------
SIST EN IEC 62841-2-3:2021
– 4 – IEC 62841-2-3:2020 © IEC 2020
Table 105 – Guard thickness for diamond cutting wheels . 34
Table 106 –Typical pre-cut length ranges for standard wheel dimensions . 36
Table I.101 – Test conditions for angle grinding and concrete grinding . 44
Table I.102 – Dimensions of the artificial wheel of Figure I.104 or Figure I.106 for angle
grinding, cutting off and concrete grinding. 46
Table I.103 – Feed force . 46
Table I.104 – Test conditions for straight grinding . 47
Table I.105 – Dimensions of the artificial wheel of Figure I.106 for straight grinding . 48
Table I.106 – Test conditions for polishing . 49
Table I.107 – Test conditions for disc-type sanding . 49
Table 4 – Required performance levels . 51
Table BB.101 – Wheel guard thickness . 61

---------------------- Page: 8 ----------------------
SIST EN IEC 62841-2-3:2021
IEC 62841-2-3:2020 © IEC 2020 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
TOOLS AND LAWN AND GARDEN MACHINERY – SAFETY –

Part 2-3: Particular requirements for hand-held grinders,
disc-type polishers and disc-type sanders

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62841-2-3 has been prepared by IEC technical committee 116:
Safety of motor-operated electric tools.
The text of this International standard is based on the following documents:
FDIS Report on voting
116/444/FDIS 116/454/RVD

Full information on the voting for the approval of this International standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 9 ----------------------
SIST EN IEC 62841-2-3:2021
– 6 – IEC 62841-2-3:2020 © IEC 2020
This Part 2-3 is to be used in conjunction with the first edition of IEC 62841-1:2014.
This Part 2-3 supplements or modifies the corresponding clauses in IEC 62841-1, so as to
convert it into the IEC Standard: Particular requirements for hand-held grinders, disc-type
polishers and disc-type sanders.
Where a particular subclause of Part 1 is not mentioned in this Part 2-3, that subclause
applies as far as relevant. Where this standard states “addition”, “modification” or
“replacement”, the relevant text in Part 1 is to be adapted accordingly.
The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
The terms in bold typeface in the text are defined in Clause 3
Subclauses, notes and figures which are additional to those in Part 1 are numbered starting
from 101.
A list of all parts of the IEC 62841 series, under the general title: Electric motor-operated
hand-held tools, transportable tools and lawn and garden machinery – Safety, can be found
on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation
nationally not earlier than 36 months from the date of publication.
The contents of the corrigendum of April 2021 have been included in this copy.

---------------------- Page: 10 ----------------------
SIST EN IEC 62841-2-3:2021
IEC 62841-2-3:2020 © IEC 2020 – 7 –
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
TOOLS AND LAWN AND GARDEN MACHINERY – SAFETY –

Part 2-3: Particular requirements for hand-held grinders,
disc-type polishers and disc-type sanders



1 Scope
This clause of Part 1 is applicable, except as follows:
Addition:
This part of IEC 62841 applies to hand-held grinders, disc-type polishers and disc-type
sanders, including angle, straight and vertical tools, intended for use on various materials
except magnesium, with a rated capacity not exceeding 230 mm. For grinders, the rated no-
load speed does not exceed a peripheral speed of the accessory of 80 m/s at rated
capacity.
This standard does not apply to dedicated cut-off machines.
NOTE 101 It is planned that a document on cut-off machines will be published.
This standard does not apply to orbital polishers and orbital sanders.
NOTE 102 It is planned that a document on orbital polishers and orbital sanders will be published.
This standard does not apply to die grinders.
NOTE 103 Die grinders are covered by IEC 62841-2-23.
2 Normative references
This clause of Part 1 is applicable except as follows:
Addition:
ISO 525:2013, Bonded abrasive products – General requirements
3 Terms and definitions
This clause of Part 1 is applicable, except as follows:
3.101
blotter
thin piece of an easily compressible material, between the abrasive product and flange
3.102
diamond wheel
metal wheel with continuous or segmented diamond abrasives

---------------------- Page: 11 ----------------------
SIST EN IEC 62841-2-3:2021
– 8 – IEC 62841-2-3:2020 © IEC 2020
3.102.1
diamond cutting wheel
metal wheel with the abrasives located on the periphery of the wheel
3.102.2
diamond grinding wheel
metal wheel with abrasives located on the face of the wheel
3.103
disc-type polisher
tool equipped with a rotating flexible disc or pad intended for polishing
Note 101 to entry: Polishing is an operation to produce a smooth or shiny surface.
3.104
disc-type sander
tool, constructed like a grinder, intended for sanding
Note 101 to entry: Sanding is an operation to remove material using flexible abrasive material, such as
sandpaper.
3.105
flange
collar, disc or plate between or against which wheels are mounted
3.105.1
unrecessed (flange)
flange fixed to the machine spindle having an unrecessed flat surface against which a
threaded hole abrasive product is screwed, e.g. a cup wheel, a cone or a plug
3.105.2
inner flange
flange which contacts and provides support to the back side of the wheel and is located on
the spindle between wheel and tool
3.105.3
outer flange
flange which supports the front side of the wheel and secures and clamps the wheel to the
spindle and the inner flange
Note 101 to entry: In Canada and the United States of America, the following additional definition applies:
3.105.UC1
adaptor backing flange
inner flange which contacts and supports in the hub area and extends past the raised portion to reduce the flexing
of the wheel periphery
3.106
grinder
tool driving a rotating spindle on which a bonded abrasive product or a diamond wheel is
mounted
3.106.1
angle grinder
grinder with the rotating spindle at an angle to the axis of the tool body which acts as a
grasping surface, intended for peripheral and lateral grinding
Note 101 to entry: See Figure 101.

---------------------- Page: 12 ----------------------
SIST EN IEC 62841-2-3:2021
IEC 62841-2-3:2020 © IEC 2020 – 9 –

Figure 101 – Example of an angle grinder
3.106.2
straight grinder
grinder with the rotating spindle in-line with the axis of the tool body which acts as a grasping
surface, intended for peripheral grinding only and not equipped with a collet or chuck
Note 101 to entry: See Figure 102.

Figure 102 – Example of a straight grinder
3.106.3
vertical grinder
grinder with the rotating spindle in-line with the axis of the tool body and with handles that
are substantially perpendicular to the axis of the rotating spindle, intended for peripheral and
lateral grinding
Note 101 to entry: See Figure 103.

---------------------- Page: 13 ----------------------
SIST EN IEC 62841-2-3:2021
– 10 – IEC 62841-2-3:2020 © IEC 2020

Figure 103 – Example of a vertical grinder
3.107
guide plate
flat plate on the machine which rests on the material to be cut
3.108
guide roller
roller on the machine which rests on the material to be cut
3.109
minor fragment
particles less than 1/16 of the mass of the abrasive wheel
3.110
rated capacity
maximum diameter of the rotating accessory to be fitted on the tool as specified by the
manufacturer’s instruction
3.111
wheel guard
device which partly encloses the abrasive wheel and gives protection to the operator
3.112
wheel types
alphanumeric designation of wheels based upon ap
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.