SIST EN ISO 6682:2008

SLOVENSKI STANDARD
SIST EN ISO 6682:2008
01-november-2008
1DGRPHãþD
SIST EN ISO 6682:2000
6WURML]D]HPHOMVNDGHOD2EPRþMHXGREMDLQGRVHJDQDG]RUD,62
YNOMXþQR]'RSROQLORP
Earth-moving machinery - Zones of comfort and reach for controls (ISO 6682:1986,
including Amd 1:1989)
Erdbaumaschine - Stellteile - Bequemlichkeitsbereiche und Reichweitenbereiche (ISO
6682:1986, einschließlich Amd 1:1989)
Engins de terrassement - Zones de confort et d'accessibilité des commandes (ISO
6682:1986, Amd 1:1989 inclus)
Ta slovenski standard je istoveten z: EN ISO 6682:2008
ICS:
53.100 Stroji za zemeljska dela Earth-moving machinery
SIST EN ISO 6682:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 6682:2008

---------------------- Page: 2 ----------------------

SIST EN ISO 6682:2008
EUROPEAN STANDARD
EN ISO 6682
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2008
ICS 53.100 Supersedes EN ISO 6682:1995
English Version
Earth-moving machinery - Zones of comfort and reach for
controls (ISO 6682:1986, including Amd 1:1989)
Engins de terrassement - Zones de confort et Erdbaumaschine - Stellteile - Bequemlichkeitsbereiche und
d'accessibilité des commandes (ISO 6682:1986, Amd Reichweitenbereiche (ISO 6682:1986, einschließlich Amd
1:1989 inclus) 1:1989)
This European Standard was approved by CEN on 25 August 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6682:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 6682:2008
EN ISO 6682:2008 (E)
Contents Page
Foreword.3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC .4
Annex ZB (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC .5

2

---------------------- Page: 4 ----------------------

SIST EN ISO 6682:2008
EN ISO 6682:2008 (E)
Foreword
The text of ISO 6682:1986, including Amd 1:1989 has been prepared by Technical Committee ISO/TC 127
“Earth-moving machinery” of the International Organization for Standardization (ISO) and has been taken over
as EN ISO 6682:2008 by Technical Committee CEN/TC 151 “Construction equipment and building material
machines - Safety” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2009, and conflicting national standards shall be withdrawn at
the latest by December 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6682:1995.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 6682:1986, including Amd 1:1989 has been approved by CEN as a EN ISO 6682:2008 without
any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 6682:2008
EN ISO 6682:2008 (E)
Annex ZA
(informative)

Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive Machinery 98/37/EC, amended by 98/79/EC.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity
with the relevant Essential Requirements 1.1.2.d, 1.2.2 and 3.3.1 of that Directive and associated EFTA
regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.

4

---------------------- Page: 6 ----------------------

SIST EN ISO 6682:2008
EN ISO 6682:2008 (E)
Annex ZB
(informative)

Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2006/42/EC on machinery.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity
with the relevant Essential Requirements 1.1.6, 1.2.2, 3.3.1 of that Directive and associated EFTA regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.
5

---------------------- Page: 7 ----------------------

SIST EN ISO 6682:2008

---------------------- Page: 8 ----------------------

SIST EN ISO 6682:2008
lnternati
8
INTERNATIONAL ORGANIZATION FOR STANDARDiZATlON~ME~~YtiAPO~t-iAR OPrAHbl3AUMfI l-l0 CTAH~APTL13AlJ1I1M.ORGANlSATlON INTERNATIONALE DE NORMALISATION
Earth-moving machinery - Zones of comfort and
reach for controls
Engins de terrassement - Zones de confort et d’accessibilite’ des commandes
Second edition - 1986-06-15
UDC 621.878/.879 : 331.101.1 Ref. No. IS0 66824986 (E)
iii
-
: earth moving equipment, operating stations, ergonomics, operating requirements, control devices, position (location).
Descriptors
2
Price based on IO pages
-

---------------------- Page: 9 ----------------------

SIST EN ISO 6682:2008
Foreword
IS0 (the International Organization for Standardization) is a worldwide federation of
national standards bodies (IS0 member bodies). The work of preparing International
Standards is normally carried out through IS0 technical committees. Each member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the IS0 Council. They are approved in accordance with IS0 procedures requiring at
least 75 % approval by the member bodies voting.
International Standard IS0 6682 was prepared by Technical Committee ISO/TC 127,
Earth-moving machinery.
This second edition cancels and replaces the first edition (IS0 6682-1980), of which it
constitutes a minor revision.
Users should note that all International Standards undergo revision from time to time
and that any reference made herein to any other International Standard implies its
latest edition, unless otherwise stated.
0 International Organization for Standardization, 1986
Printed in Switzerland

---------------------- Page: 10 ----------------------

SIST EN ISO 6682:2008
IS0 6682-1986 (El
INTERNATIONAL STANDARD
Earth-moving machinery - Zones of comfort and
reach for controls
4.5 secondary controls : Controls that are infrequently
1 Scope
used by the operator, such as lights, windscreen wipers,
This International Standard defines zones of comfort and reach starter, heater, air conditioner, etc.
for controls derived from the overlapping reach capability of
large and small operators in the seated position.
4.6 zones of comfort: Preferred control location zones for
primary hand and foot controls. Both large and small operators
should be able to reach controls comfortably in these zones.
2 Field of application
This document is intended as a guide for the design of the
4.7 zones of reach: Control location zones for secondary
operator compartment controls for earth-moving machinery.
hand and foot controls. Both large and small operators should
be able to reach controls in these zones from the seated pos-
ition, but the operator may be required to rotate or lean forward
and to each side.
3 References
IS0 3411, Earth-moving machinery - Human physical dimen-
4.8 XYZ coordinate system: Coordinate system used to
sions of operators and minimum operator space envelope.
define the control zone locations:
IS0 5353, Earth-moving machinery - Seat index point (SIP).
a) Origin at the SIP.
IS0 674611, Earth-moving machinery - Definitions of dimen-
b) X-axis; fore-aft, positive to front of the SIP.
sions and symbok - Part 1: Base machine.
c) Y-axis; lateral, positive to right of the SIP.
d) Z-axis; vertical, positive upward from the SIP.
4 Definitions
See IS0 6746/l.
4.1 SIP: Seat Index Point as defined by IS0 5353 (fixed at
nominal seat adjustments).
4.9 flexion : Movement that changes the angle between
body parts.
4.2 control displacement: Travel or movement of a control
through its operational range.
4.10 adduction : Movement in a plane normal to the plane
4.3 control location: Positions of a control, including the
of flexion and directed towards or past the mid-axis (XZ plane)
corresponding control displacement, defined from the SIP.
of the body.
4.4 primary controls: Controls that are used frequently or
continuously by the operator, such as: 4.11 abduction : Movement in a plane
...