SIST EN 62026-1:2007

SLOVENSKI STANDARD
SIST EN 62026-1:2007
01-december-2007
Nizkonapetostne stikalne in krmilne naprave – Vmesniki krmilnikov (CDIs) – 1. del:
Splošna pravila (IEC 62026-1:2007)
Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) -- Part 1:
General rules (IEC 62026-1:2007)
Niederspannungsschaltgeräte - Steuerung-Geräte-Netzwerke (CDIs) -- Teil 1:
Allgemeine Festlegungen (IEC 62026-1:2007)
Appareillage a basse tension - Interfaces appareil de commande-appareil (CDI) -- Partie
1: Regles générales (IEC 62026-1:2007)
Ta slovenski standard je istoveten z: EN 62026-1:2007
ICS:
29.130.20 Nizkonapetostne stikalne in Low voltage switchgear and
krmilne naprave controlgear
SIST EN 62026-1:2007 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 62026-1

NORME EUROPÉENNE
September 2007
EUROPÄISCHE NORM

ICS 29.130.20


English version


Low-voltage switchgear and controlgear -
Controller-device interfaces (CDIs) -
Part 1: General rules
(IEC 62026-1:2007)


Appareillage à basse tension -  Niederspannungsschaltgeräte -
Interfaces appareil Steuerungs-Geräte-Netzwerke (CDIs) -
de commande-appareil (CDI) - Teil 1: Allgemeine Festlegungen
Partie 1: Règles générales (IEC 62026-1:2007)
(CEI 62026-1:2007)




This European Standard was approved by CENELEC on 2007-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62026-1:2007 E

---------------------- Page: 2 ----------------------

EN 62026-1:2007 - 2 -
Foreword
The text of document 17B/1505/CDV, future edition 2 of IEC 62026-1, prepared by SC 17B, Low-voltage
switchgear and controlgear, of IEC TC 17, Switchgear and controlgear, was submitted to the
IEC-CENELEC parallel Unique Acceptance Procedure and was approved by CENELEC as EN 62026-1
on 2007-09-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2008-06-01
– latest date by which the national standards conflicting
(dow) 2010-09-01
with the EN have to be withdrawn
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and covers essential requirements of
EC Directives EMC (89/336/EEC) and EMC2 (2004/108/EC). See Annex ZZ.
Annexes ZA and ZZ have been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 62026-1:2007 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 62026-1:2007

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year
IEC 60947-1 2007 Low-voltage switchgear and controlgear - EN 60947-1 2007
Part 1: General rules


IEC 61000-4-2 1995 Electromagnetic compatibility (EMC) - EN 61000-4-2 1995
A1 1998 Part 4-2: Testing and measurement A1 1998
A2 2000 techniques - Electrostatic discharge A2 2001
immunity test


IEC 61000-4-3 2006 Electromagnetic compatibility (EMC) - EN 61000-4-3 2006
Part 4-3: Testing and measurement
techniques - Radiated, radio-frequency,
electromagnetic field immunity test


IEC 61000-4-4 2004 Electromagnetic compatibility (EMC) - EN 61000-4-4 2004
Part 4-4: Testing and measurement
techniques - Electrical fast transient/burst
immunity test


IEC 61000-4-5 2005 Electromagnetic compatibility (EMC) - EN 61000-4-5 2006
Part 4-5: Testing and measurement
techniques - Surge immunity test


IEC 61000-4-6 2003 Electromagnetic compatibility (EMC) -
+ A1 2004 Part 4-6: Testing and measurement
+ A2 2006 techniques - Immunity to conducted EN 61000-4-6 2007
disturbances, induced by radio-frequency + corr. August 2007
fields


IEC 61000-6-2 2005 Electromagnetic compatibility (EMC) - EN 61000-6-2 2005
Part 6-2: Generic standards - Immunity for + corr. September 2005
industrial environments


CISPR 11 (mod) 2003 Industrial scientific and medical (ISM)
+ A1 2004 radio-frequency equipment - EN 55011 2007
A2 2006 Electromagnetic disturbance A2 2007
characteristics - Limits and methods of
measurement

---------------------- Page: 4 ----------------------

EN 62026-1:2007 - 4 -
Annex ZZ
(informative)

Coverage of Essential Requirements of EC Directives
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant essential requirements as given in Article 4 of the EC Directive 89/336/EEC and in Article 1 of
Annex I of the EC Directive 2004/108/EC.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directives concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling within
the scope of this standard.
NOTE  EN 62026-1:2007 does not give presumption of conformity without another part of the standard.
___________

---------------------- Page: 5 ----------------------

INTERNATIONAL IEC
STANDARD
CEI



62026-1
NORME


Second edition
INTERNATIONALE

Deuxième édition
2007-06


Low-voltage switchgear and controlgear –
Controller-device interfaces (CDIs) –
Part 1:
General rules

Appareillage à basse tension –
Interfaces appareil de commande-appareil (CDI) –
Partie 1:
Règles générales
PRICE CODE
M
CODE PRIX
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue
Pour prix, voir catalogue en vigueur

---------------------- Page: 6 ----------------------

– 2 – 62026-1 © IEC:2007
CONTENTS
FOREWORD.3
INTRODUCTION.5

1 Scope.6
2 Normative references.6
3 Terms and definitions .7
4 Classifications .8
5 Characteristics.8
5.1 CDI components.8
5.2 Interfaces .8
5.3 Topology .9
5.4 Information exchanges.9
5.5 Attributes.9
6 Product information.9
6.1 Instructions for installation, operation and maintenance.9
6.2 Profiles.9
6.3 Marking .9
6.4 Degree of protection .10
7 Normal service, mounting and transport conditions.10
7.1 General .10
7.2 Normal service conditions.10
7.2.1 General .10
7.2.2 Ambient air temperature.10
7.2.3 Altitude .10
7.2.4 Climatic conditions.10
7.3 Conditions during transport and storage.10
7.4 Mounting .11
8 Constructional and performance requirements .11
8.1 General .11
8.2 Electromagnetic compatibility (EMC) .11
8.2.1 Immunity.11
8.2.2 Emission.12
8.2.3 EMC tests.12
9 Tests .12
9.1 General .12
9.2 Type tests .12
9.3 Electromagnetic compatibility.12

Table 1 – Immunity requirements .11

---------------------- Page: 7 ----------------------

62026-1 © IEC:2007 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR –
CONTROLLER-DEVICE INTERFACES (CDIs) –

Part 1: General rules


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62026-1 has been prepared by subcommittee 17B: Low-voltage
switchgear and controlgear, of IEC technical committee 17: Switchgear and controlgear.
This second edition of IEC 62026-1 cancels and replaces the first edition published in 2000.
It represents some general updating without technical changes with regard to the previous
edition.
The text of this standard is based on the following documents:
CDV Report on voting
17B/1505/CDV 17B/1544/RVC

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

---------------------- Page: 8 ----------------------

– 4 – 62026-1 © IEC:2007
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 62026, under the general title Low-voltage switchgear and
controlgear – Controller-device interfaces (CDIs), can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until the
maintenance result date indicated on the IEC web site under “http://webstore.iec.ch” in the data
related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.

---------------------- Page: 9 ---------
...