SIST EN 480-8:2012

SLOVENSKI STANDARD
SIST EN 480-8:2012
01-september-2012
1DGRPHãþD
SIST EN 480-8:1998
.HPLMVNLGRGDWNL]DEHWRQPDOWRLQLQMHNFLMVNRPDVR0HWRGHSUHVNXãDQMDGHO
'RORþDQMHGHOHåDVXKHVQRYL
Admixtures for concrete, mortar and grout - Test methods - Part 8: Determination of the
conventional dry material content
Zusatzmittel für Beton, Mörtel und Einpreßmörtel - Prüfverfahren - Teil 8: Bestimmung
des Feststoffgehalts
Adjuvants pour béton, mortier et coulis - Méthodes d'essai - Partie 8: Détermination de
l'extrait sec conventionnel
Ta slovenski standard je istoveten z: EN 480-8:2012
ICS:
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
91.100.30 Beton in betonski izdelki Concrete and concrete
products
SIST EN 480-8:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 480-8:2012

---------------------- Page: 2 ----------------------

SIST EN 480-8:2012


EUROPEAN STANDARD
EN 480-8

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2012
ICS 01.040.91; 91.100.30 Supersedes EN 480-8:1996
English Version
Admixtures for concrete, mortar and grout - Test methods - Part
8: Determination of the conventional dry material content
Adjuvants pour bétons, mortier et coulis - Méthodes d'essai Zusatzmittel für Beton, Mörtel und Einpressmörtel -
- Partie 8: Détermination de l'extrait sec conventionnel Prüfverfahren - Teil 8: Bestimmung des Feststoffgehalts
This European Standard was approved by CEN on 13 April 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 480-8:2012: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 480-8:2012
EN 480-8:2012 (E)
Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Principle .5
3 Apparatus .5
4 Procedure .5
5 Results .6
6 Test report .6
Bibliography .7

2

---------------------- Page: 4 ----------------------

SIST EN 480-8:2012
EN 480-8:2012 (E)
Foreword
This document (EN 480-8:2012) has been prepared by Technical Committee CEN/TC 104 “Concrete and
related products”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2012, and conflicting national standards shall be withdrawn
at the latest by November 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 480-8:1996.
This draft European Standard is part of the series EN 480 "Admixtures for concrete, mortar and grout — Test
methods" which comprises the following:
 Part 1 Reference concrete and reference mortar for testing
 Part 2 Determination of setting time
 Part 4 Determination of bleeding of concrete
 Part 5 Determination of capillary absorption
 Part 6 Infrared analysis
 Part 8 Determination of the conventional dry material content
 Part 10 Determination of water soluble chloride content
 Part 11 Determination of air void characteristics in hardened concrete
 Part 12 Determination of the alkali content of admixtures
 Part 13 Reference masonry mortar for testing mo
...