SIST EN ISO 7590:2018
(Main)Steel cord conveyor belts - Methods for the determination of total thickness and cover thickness (ISO 7590:2018)
Steel cord conveyor belts - Methods for the determination of total thickness and cover thickness (ISO 7590:2018)
This document specifies three methods for the measurement of total belt thickness and the thickness of
covers of steel cord conveyor belts.
Methods A1 and A2 (micrometer methods) can be used for all steel cord conveyor belts for the
measurement of both total belt thickness and cover thickness.
Method B (optical method) is intended for the measurement of cover thickness only. It is not suitable if
there is a textile or metal weft, nor if the ends of the steel cords become twisted when cut.
Stahlseil-Fördergurte - Messung der Gesamtdicke und der Deckplattendicke (ISO 7590:2018)
Courroies transporteuses à câbles d'acier - Méthodes de détermination de l'épaisseur totale et de l'épaisseur des revêtements (ISO 7590:2018)
Le présent document spécifie trois méthodes de mesure de l'épaisseur totale des courroies et de l'épaisseur des revêtements de courroies transporteuses à câbles d'acier.
Les méthodes A1 et A2 (méthodes du micromètre) peuvent être utilisées pour toutes les courroies transporteuses à câbles d'acier, pour le mesurage de l'épaisseur totale des courroies et de l'épaisseur du revêtement.
La méthode B (méthode optique) est recommandée uniquement pour le mesurage de l'épaisseur du revêtement. Elle n'est pas appropriée pour les courroies à trame textile ou métallique, ni si les extrémités des câbles d'acier s'entortillent après découpage.
Naprave in sistemi za kontinuirni transport - Trakovi tračnih transporterjev z jeklenim vložkom - Metode za določevanje celotne debeline in debeline zaščitne obloge (ISO 7590:2018)
Ta dokument določa tri metode za merjenje celotne debeline trakov in debeline zaščitne obloge trakov tračnih transporterjev z jeklenim vložkom.
Metodi A1 in A2 (metodi merjenja z mikrometrom) je mogoče uporabljati za merjenje celotne debeline trakov in debeline zaščitne obloge vseh trakov tračnih transporterjev z jeklenim vložkom.
Metoda B (metoda optičnega merjenja) je namenjena samo za merjenje debeline zaščitne obloge in ni ustrezna v primeru tekstilnih ali kovinskih votkovnih niti ter če se konci kovinskih vrvi pri rezanju zvijejo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 7590:2018
01-oktober-2018
1DGRPHãþD
SIST EN ISO 7590:2009
1DSUDYHLQVLVWHPL]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY]
MHNOHQLPYORåNRP0HWRGH]DGRORþHYDQMHFHORWQHGHEHOLQHLQGHEHOLQH]DãþLWQH
REORJH ,62
Steel cord conveyor belts - Methods for the determination of total thickness and cover
thickness (ISO 7590:2018)
Stahlseil-Fördergurte - Messung der Gesamtdicke und der Deckplattendicke (ISO
7590:2018)
Courroies transporteuses à câbles d'acier - Méthodes de détermination de l'épaisseur
totale et de l'épaisseur des revêtements (ISO 7590:2018)
Ta slovenski standard je istoveten z: EN ISO 7590:2018
ICS:
53.040.20 Deli za transporterje Components for conveyors
SIST EN ISO 7590:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 7590:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 7590:2018
EN ISO 7590
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2018
EUROPÄISCHE NORM
ICS 53.040.20 Supersedes EN ISO 7590:2009
English Version
Steel cord conveyor belts - Methods for the determination
of total thickness and cover thickness (ISO 7590:2018)
Courroies transporteuses à câbles d'acier - Méthodes Stahlseil-Fördergurte - Messung der Gesamtdicke und
de détermination de l'épaisseur totale et de l'épaisseur der Deckplattendicke (ISO 7590:2018)
des revêtements (ISO 7590:2018)
This European Standard was approved by CEN on 30 May 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7590:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 7590:2018
EN ISO 7590:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 7590:2018
EN ISO 7590:2018 (E)
European foreword
This document (EN ISO 7590:2018) has been prepared by Technical Committee ISO/TC 41 "Pulleys and
belts (including veebelts)" in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the
secretariat of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2019, and conflicting national standards shall
be withdrawn at the latest by January 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 7590:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 7590:2018 has been approved by CEN as EN ISO 7590:2018 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 7590:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 7590:2018
INTERNATIONAL ISO
STANDARD 7590
Sixth edition
2018-05
Steel cord conveyor belts — Methods
for the determination of total
thickness and cover thickness
Courroies transporteuses à câbles d'acier — Méthodes de
détermination de l'épaisseur totale et de l'épaisseur des revêtements
Reference number
ISO 7590:2018(E)
©
ISO 2018
---------------------- Page: 7 ----------------------
SIST EN ISO 7590:2018
ISO 7590:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 7590:2018
ISO 7590:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Procedure. 2
6.1 General . 2
6.2 Measurement points . 2
6.3 Test pieces and test specimens . 2
6.3.1 General. 2
6.3.2 Test pieces and test specimens for method A1 . 3
6.3.3 Test specimens for method A2 . 3
6.3.4 Test specimens for method B . 3
6.4 Measurement of thickness . 3
6.4.1 Method A1 . 3
6.4.2 Method A2 . 4
6.4.3 Method B . 5
7 Test report . 5
Bibliography . 7
© ISO 2018 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 7590:2018
ISO 7590:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different typ
...
SLOVENSKI STANDARD
oSIST prEN ISO 7590:2017
01-november-2017
1DSUDYHLQVLVWHPL]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY]
MHNOHQLPYORåNRP0HWRGH]DGRORþHYDQMHFHORWQHGHEHOLQHLQGHEHOLQH]DãþLWQH
REORJH ,62',6
Steel cord conveyor belts - Methods for the determination of total thickness and cover
thickness (ISO/DIS 7590:2017)
Stahlseil-Fördergurte - Messung der Gesamtdicke und der Deckplattendicke (ISO/DIS
7590:2017)
Courroies transporteuses à câbles d'acier - Méthodes de détermination de l'épaisseur
totale et de l'épaisseur des revêtements (ISO/DIS 7590:2017)
Ta slovenski standard je istoveten z: prEN ISO 7590
ICS:
53.040.20 Deli za transporterje Components for conveyors
oSIST prEN ISO 7590:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 7590:2017
---------------------- Page: 2 ----------------------
oSIST prEN ISO 7590:2017
DRAFT INTERNATIONAL STANDARD
ISO/DIS 7590
ISO/TC 41/SC 3 Secretariat: JISC
Voting begins on: Voting terminates on:
2017-09-07 2017-11-30
Steel cord conveyor belts — Methods for the determination
of total thickness and cover thickness
Courroies transporteuses à câbles d’acier — Méthodes de détermination de l’épaisseur totale et de
l’épaisseur des revêtements
ICS: 53.040.20
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 7590:2017(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2017
---------------------- Page: 3 ----------------------
oSIST prEN ISO 7590:2017
ISO/DIS 7590:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 7590:2017
ISO/DIS 7590:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Procedure. 2
6.1 General . 2
6.2 Measurement points . 2
6.3 Test pieces and test specimens . 2
6.3.1 General. 2
6.3.2 Test pieces and test specimens for method A1 . 3
6.3.3 Test specimens for method A2 . 3
6.3.4 Test specimens for method B . 3
6.4 Measurement of thickness . 3
6.4.1 Method A1 . 3
6.4.2 Method A2 . 4
6.4.3 Method B . 5
7 Test report . 5
Bibliography . 7
© ISO 2017 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 7590:2017
ISO/DIS 7590:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html.
The committee responsible for this document is Technical CommitteeISO/TC41, Pulleys and belts
(including veebelts), Subcommittee SC 3, Conveyor belts.
This sixth edition cancels and replaces the fifth edition (ISO 7590:2009), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— The Figure 4 was corrected.
iv © ISO 2017 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 7590:2017
DRAFT INTERNATIONAL STANDARD ISO/DIS 7590:2017(E)
Steel cord conveyor belts — Methods for the determination
of tot
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.