SIST EN ISO 9852:2018

SLOVENSKI STANDARD
SIST EN ISO 9852:2018
01-januar-2018
1DGRPHãþD
SIST EN 580:2003
&HYLL]QHPHKþDQHJDSROLYLQLONORULGD39&82GSRUQRVWSURWLGLNORUPHWDQXSUL
GRORþHQLWHPSHUDWXUL'&073UHVNXVQDPHWRGD,62
Unplasticized poly(vinyl chloride) (PVC-U) pipes - Dichloromethane resistance at
specified temperature (DCMT) - Test method (ISO 9852:2007)
Rohre aus weichmacherfreiem Polyvinylchlorid (PVC-U) - Beständigkeit gegen
Dichlormethan bei einer festgelegten Temperatur (DCMT) - Prüfverfahren (ISO
9852:2007)
Tubes en poly(chlorure de vinyle) non plastifié (PVC-U) - Résistance au dichlorométhane
à une température spécifiée (DCMT) - Méthode d'essai (ISO 9852:2007)
Ta slovenski standard je istoveten z: EN ISO 9852:2017
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
SIST EN ISO 9852:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 9852:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 9852:2018


EN ISO 9852
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2017
EUROPÄISCHE NORM
ICS 23.040.20 Supersedes EN 580:2003
English Version

Unplasticized poly(vinyl chloride) (PVC-U) pipes -
Dichloromethane resistance at specified temperature
(DCMT) - Test method (ISO 9852:2007)
Tubes en poly(chlorure de vinyle) non plastifié (PVC- Rohre aus weichmacherfreiem Polyvinylchlorid (PVC-
U) - Résistance au dichlorométhane à une température U) - Beständigkeit gegen Dichlormethan bei einer
spécifiée (DCMT) - Méthode d'essai (ISO 9852:2007) festgelegten Temperatur (DCMT) - Prüfverfahren (ISO
9852:2007)
This European Standard was approved by CEN on 19 September 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9852:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 9852:2018
EN ISO 9852:2017 (E)
Contents Page
European Foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 9852:2018
EN ISO 9852:2017 (E)
European Foreword
The text of ISO 9852:2007 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes,
fittings and valves for the transport of fluids” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 9852:2017 by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2018 and conflicting national standards shall be
withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 580:2003.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 9852:2007 has been approved by CEN as a EN ISO 9852:2017 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 9852:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 9852:2018

INTERNATIONAL ISO
STANDARD 9852
Second edition
2007-05-01

Unplasticized poly(vinyl chloride) (PVC-U)
pipes — Dichloromethane resistance at
specified temperature (DCMT) — Test
method
Tubes en poly(chlorure de vinyle) non plastifié (PVC-U) — Résistance
au dichlorométhane à une température spécifiée (DCMT) — Méthode
d'essai




Reference number
ISO 9852:2007(E)
©
ISO 2007

---------------------- Page: 7 ----------------------

SIST EN ISO 9852:2018
ISO 9852:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 9852:2018
ISO 9852:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Principle. 1
3 Reagent. 1
4 Apparatus . 2
5 Preparation of test pieces. 2
6 Immersion conditions. 3
7 Procedure . 3
8 Expression of results . 3
9 Test report . 4
Annex A (informative) Description of attack. 5
Annex B (informative) Example of small container placed in an existing (larger) container . 6

© ISO 2007 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 9852:2018
ISO 9852:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9852 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the
transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and
their accessories ― Test methods and basic specifications.
This second edition cancels and replaces the first edition (ISO 9852:1995), which has been revised to align it
with EN 580:2003.
The principal modifications are the following:
⎯ the wall thickness ranges “8 u e u 16” and “e > 16” in Table 1 have been changed to “8 u e < 16” and
“16 u e”, respectively, to align them with those in EN 580:2003;
⎯ the surface of the dichloromethane layer has been reduced to the minimum and the thickness of the
water layer covering the dichloromethane increased (see 6.2);
⎯ after immersion in the dichloromethane, the test piece is held in the water layer to allow it to “drip” before
final drying and inspection (see 7.4);
⎯ in the event of the pipe being attacked (see 8.2), giving a description of the attack has become optional,
dealt with in a new Annex A (informative).
⎯ the lower limit for the test temperature (12 °C) has been moved to 6.3, and Annex A, “Basic specification”,
has been deleted;
⎯ a typical test arrangement, with the deeper water layer (acting both as a block to evaporation and as a
“drip” zone), is
...