SIST EN 60862-1:2016

SLOVENSKI STANDARD
SIST EN 60862-1:2016
01-marec-2016
1DGRPHãþD
SIST EN 60862-1:2004
)LOWUL]DSRYUãLQVNHDNXVWLþQHYDORYH6$:RFHQMHQHNDNRYRVWLGHO6SORãQD
VSHFLILNDFLMD
Surface acoustic wave (SAW) filters of assessed quality - Part 1: Generic specification
Filtres à ondes acoustiques de surface (OAS) sous assurance de la qualité - Partie 1:
Spécification générique
Ta slovenski standard je istoveten z: EN 60862-1:2015
ICS:
31.160 (OHNWULþQLILOWUL Electric filters
SIST EN 60862-1:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60862-1:2016

---------------------- Page: 2 ----------------------

SIST EN 60862-1:2016


EUROPEAN STANDARD EN 60862-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2015
ICS 31.140 Supersedes EN 60862-1:2003
English Version
Surface acoustic wave (SAW) filters of assessed quality - Part 1:
Generic specification
(IEC 60862-1:2015)
Filtres à ondes acoustiques de surface (OAS) sous Oberflächenwellenfilter (OFW-Filter) mit bewerteter Qualität
assurance de la qualité - Partie 1: Spécification générique - Teil 1: Fachgrundspezifikation
(IEC 60862-1:2015) (IEC 60862-1:2015)
This European Standard was approved by CENELEC on 2015-09-24. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60862-1:2015 E

---------------------- Page: 3 ----------------------

SIST EN 60862-1:2016
EN 60862-1:2015

European foreword
The text of document 49/1151/FDIS, future edition 3 of IEC 60862-1, prepared by IEC/TC 49
"Piezoelectric and dielectric devices for frequency control and selection" was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN 60862-1:2015.
The following dates are fixed:
• latest date by which the document has (dop) 2016-06-24
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2018-09-24
• latest date by which the national
standards conflicting with the
document have to be withdrawn

This document supersedes EN 60862-1:2003.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 60862-1:2015 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60068-2-10:2005 NOTE  Harmonized as EN 60068-2-10:2005 (not modified).
IEC 60862-2:2012 NOTE  Harmonized as EN 60862-2:2012 (not modified).
IEC 60862-3 NOTE  Harmonized as EN 60862-3.
2

---------------------- Page: 4 ----------------------

SIST EN 60862-1:2016
EN 60862-1:2015


Annex ZA
(normative)


Normative references to international publications
with their corresponding European publications


The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.


NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.


Publication Year Title EN/HD Year
IEC 60027 series Letter symbols to be used in electrical EN 60027 series
technology
IEC 60050 series International electrotechnical vocabulary - -
IEC 60068-1 2013 Environmental testing -- Part 1: General EN 60068-1 2014
and guidance
IEC 60068-2-1 -  Environmental testing -- Part 2-1: Tests - EN 60068-2-1 -
Test A: Cold
IEC 60068-2-2 -  Environmental testing -- Part 2-2: Tests - EN 60068-2-2 -
Test B: Dry heat
IEC 60068-2-6 -  Environmental testing -- Part 2-6: Tests - EN 60068-2-6 -
Test Fc: Vibration (sinusoidal)
IEC 60068-2-7 -  Basic environmental testing procedures - EN 60068-2-7 -
Part 2-7: Tests - Test Ga and guidance:
Acceleration, steady state
IEC 60068-2-13 -  Basic environmental testing procedures - EN 60068-2-13 -
Part 2-13: Tests - Test M: Low air pressure
IEC 60068-2-14 -  Environmental testing -- Part 2-14: Tests - EN 60068-2-14 -
Test N: Change of temperature
IEC 60068-2-17 1994 Basic environmental testing procedures - EN 60068-2-17 1994
Part 2-17: Tests - Test Q: Sealing
IEC 60068-2-20 -  Environmental testing -- Part 2-20: Tests - EN 60068-2-20 -
Test T: Test methods for solderability and
resistance to soldering heat of devices with
leads
IEC 60068-2-21 -  Environmental testing -- Part 2-21: Tests - EN 60068-2-21 -
Test U: Robustness of terminations and
integral mounting devices
IEC 60068-2-27 -  Environmental testing -- Part 2-27: Tests - EN 60068-2-27 -
Test Ea and guidance: Shock
IEC 60068-2-30 -  Environmental testing -- Part 2-30: Tests - EN 60068-2-30 -
Test Db: Damp heat, cyclic (12 h + 12 h
cycle)
IEC 60068-2-31 -  Environmental testing -- Part 2-31: Tests - EN 60068-2-31 -
Test Ec: Rough handling shocks, primarily
for equipment-type specimens
3

---------------------- Page: 5 ----------------------

SIST EN 60862-1:2016
EN 60862-1:2015

IEC 60068-2-45 -  Basic environmental testing procedures - EN 60068-2-45 -
Part 2-45: Tests - Test XA and guidance:
Immersion in cleaning solvents
IEC 60068-2-52 -  Environmental testing -- Part 2-52: Tests - EN 60068-2-52 -
Test Kb: Salt mist, cyclic (sodium chloride
solution)
IEC 60068-2-58 -  Environmental testing – Part 2-58: Tests – - -
Test Td: Test methods for solderability,
resistance to dissolution of metallization
and to soldering heat of surface mounting
devices (SMD)
IEC 60068-2-64 -  Environmental testing -- Part 2-64: Tests - EN 60068-2-64 -
Test Fh: Vibration, broadband random and
guidance
IEC 60068-2-78 -  Environmental testing -- Part 2-78: Tests - EN 60068-2-78 -
Test Cab: Damp heat, steady state
IEC 60122-1 -  Quartz crystal units of assessed quality -- EN 60122-1 -
Part 1: Generic specification
IEC 60617 -  Standard data element types with - -
associated classification scheme for
electric components -- Part 4: IEC
reference collection fo standard data
element types and component classes
IEC 60642 -  Piezoelectric ceramic resonators and - -
resonator units for frequency control and
selection - Chapter I: Standard values and
conditions - Chapter II: Measuring and test
conditions
IEC 60695-11-5 -  Fire hazard testing -- Part 11-5: Test EN 60695-11-5 -
flames - Needle-flame test method -
Apparatus, confirmatory test arrangement
and guidance
1)
IEC 60749-28 201X Semiconductor devices - Mechanical and FprEN 60749-28 201X
climatic test methods -- Part 28:
Electrostatic Discharge (ESD) Sensitivity
Testing Direct contact charged device
model (DC-CDM)
IEC 61000-4-2 -  Electromagnetic compatibility (EMC) -- EN 61000-4-2 -
Part 4-2: Testing and measurement
techniques - Electrostatic discharge
immunity test
IEC 61340-3-1 -  Electrostatics -- Part 3-1: Methods for EN 61340-3-1 -
simulation of electrostatic effects - Human
body model (HBM) electrostatic discharge
test waveforms
IEC 61340-3-2 -  Electrostatics -- Part 3-2: Methods for EN 61340-3-2 -
simulation of electrostatic effects -
Machine model (MM) electrostatic
discharge test waveforms
IEC 80000 series Quantities and units EN 80000 series
ISO 80000 series Quantities and units EN ISO 80000 series


1)
To be published.
4

---------------------- Page: 6 ----------------------

SIST EN 60862-1:2016



IEC 60862-1

®


Edition 3.0 2015-08




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Surface acoustic wave (SAW) filters of assessed quality –

Part 1: Generic specification




Filtres à ondes acoustiques de surface (OAS) sous assurance de la qualité –

Partie 1: Spécification générique
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 31.140 ISBN 978-2-8322-2863-0



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60862-1:2016
– 22 – IEC 60862-1:2015 © IEC 2015
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, units and symbols . 9
3.1 Terms and definitions . 9
3.1.1 General terms . 9
3.1.2 Response characteristics related terms . 12
3.1.3 SAW filter related terms . 16
3.2 Units and symbols. 18
4 Order of precedence of documents . 18
5 Preferred values for ratings and characteristics . 19
5.1 General . 19
5.2 Nominal frequencies . 19
5.2.1 Nominal frequency bands for use in RF applications . 19
5.2.2 Nominal frequency bands for use in IF applications . 19
5.2.3 Nominal frequency values for use in broadcasting IF applications . 19
5.3 Relative attenuation values specifying pass bandwidth for IF applications . 20
5.4 TTE signal suppression . 20
5.5 Operating temperature ranges, in degrees Celsius (°C) . 20
5.6 Climatic category . 20
5.7 Bump severity . 20
5.8 Vibration severity . 21
5.9 Shock severity . 21
5.10 Fine leak rate . 21
6 Marking . 22
6.1 Filter marking . 22
6.2 Package marking . 22
7 Quality assessment procedures . 22
7.1 General . 22
7.2 Primary stage of manufacture . 22
7.3 Structurally similar components . 22
7.4 Subcontracting . 22
7.5 Incorporated components . 23
7.6 Manufacturer’s approval . 23
7.7 Approval procedures . 23
7.7.1 General . 23
7.7.2 Capability approval . 23
7.7.3 Qualification approval . 23
7.8 Procedures for capability approval . 23
7.8.1 General . 23
7.8.2 Eligibility for capability approval . 24
7.8.3 Application for capability approval . 24
7.8.4 Granting of capability approval . 24
7.8.5 Capability manual . 24
7.9 Procedures for qualification approval . 24

---------------------- Page: 8 ----------------------

SIST EN 60862-1:2016
IEC 60862-1:2015 © IEC 2015 – 3 –
7.9.1 General . 24
7.9.2 Eligibility for qualification approval . 24
7.9.3 Application for qualification approval . 24
7.9.4 Granting of qualification approval . 24
7.9.5 Quality conformance inspection . 24
7.10 Test procedures . 24
7.11 Screening requirements . 24
7.12 Rework and repair work . 25
7.12.1 Rework . 25
7.12.2 Repair work . 25
7.13 Certified records of released lots . 25
7.14 Validity of release . 25
7.15 Release for delivery . 25
7.16 Unchecked parameters . 25
8 Test and measurement procedures . 25
8.1 General . 25
8.2 Test and measurement conditions . 25
8.2.1 Standard conditions for testing . 25
8.2.2 Precision of measurement . 26
8.2.3 Precautions . 26
8.2.4 Alternative test methods . 26
8.3 Visual inspection . 26
8.3.1 General . 26
8.3.2 Visual test A . 26
8.3.3 Visual test B . 26
8.3.4 Visual test C . 27
8.4 Dimensions and gauging procedures . 27
8.4.1 Dimensions test A . 27
8.4.2 Dimensions test B . 27
8.5 Electrical test procedures . 27
8.5.1 General . 27
8.5.2 Insertion attenuation measurement . 27
8.5.3 Phase measurement . 29
8.5.4 Group delay measurement . 29
8.5.5 Return attenuation measurement . 30
8.5.6 Unwanted signal measurement . 32
8.5.7 Intermodulation distortion measurement . 34
8.5.8 Measurement of insertion attenuation, phase, and group delay
characteristics at specified terminating impedances and at standard
atmospheric conditions . 35
8.5.9 Measurement of insertion attenuation, phase, and group delay
characteristics as a function of temperature . 35
8.5.10 Measurement of return attenuation at specified terminating impedance
and at the standard atmospheric conditions . 35
8.5.11 Measurement of unwanted signals at standard atmospheric conditions . 35
8.5.12 Measurement of intermodulation distortion at standard atmospheric
conditions . 36
8.5.13 Measurement method for the balanced type filter . 36
8.5.14 Insulation resistance . 38

---------------------- Page: 9 ----------------------

SIST EN 60862-1:2016
– 44 – IEC 60862-1:2015 © IEC 2015
8.5.15 Voltage proof . 38
8.6 Mechanical and environmental test procedures . 38
8.6.1 Robustness of terminations (destructive) . 38
8.6.2 Sealing tests (non-destructive) . 38
8.6.3 Soldering (solderability and resistance to soldering heat) (destructive) . 39
8.6.4 Rapid change of temperature: severe shock by liquid immersion (non-
destructive). 40
8.6.5 Rapid change of temperature with prescribed time of transition (non-
destructive). 40
8.6.6 Bump (destructive) . 40
8.6.7 Vibration (destructive). 40
8.6.8 Shock (destructive) . 41
8.6.9 Free fall (destructive) . 41
8.6.10 Acceleration, steady state (non-destructive) . 41
8.6.11 Low air pressure (non-destructive) . 42
8.6.12 Dry heat (non-destructive) . 42
8.6.13 Damp heat, cyclic (destructive) . 42
8.6.14 Cold (non-destructive) . 42
8.6.15 Climatic sequence (destructive) . 42
8.6.16 Damp heat, steady state (destructive) . 42
8.6.17 Salt mist cyclic (destructive) . 42
8.6.18 Immersion in cleaning solvents (non-destructive) . 43
8.6.19 Flammability test (destructive) . 43
8.6.20 Electrostatic discharge (ESD) sensitivity test (destructive) . 43
8.7 Endurance test procedure . 43
Bibliography . 44

Figure 1 – Frequency response of a SAW filter . 18
Figure 2 – Insertion attenuation, phase, and group delay measurement . 28
Figure 3 – Return attenuation measurement . 31
Figure 4 – Unwanted signal measurement . 33
Figure 5 – Unwanted signals measured on time domain . 34
Figure 6 – Intermodulation distortion measurement . 35
Figure 7 – Four-port network analyzer measurement for balanced-balanced connection
filter . 37
Figure 8 – Three-port network analyzer measurement for balanced-unbalanced
connection filter . 37

---------------------- Page: 10 ----------------------

SIST EN 60862-1:2016
IEC 60862-1:2015 © IEC 2015 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

SURFACE ACOUSTIC WAVE (SAW) FILTERS
OF ASSESSED QUALITY –

Part 1: Generic specification

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60862-1 has been prepared by IEC technical committee 49:
Piezoelectric, dielectric and electrostatic devices and associated materials for frequency
control, selection and detection.
This third edition cancels and replaces the second edition published in 2003. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
• the terms and definitions from IEC 60862-2:2002 are included;
• the measurement method for the balanced type filter is described;
• the electrostatic discharge (ESD) sensitivity test procedure is considered.

---------------------- Page: 11 ----------------------

SIST EN 60862-1:2016
– 66 – IEC 60862-1:2015 © IEC 2015
The text of this standard is based on the following documents:
FDIS Report on voting
49/1151/FDIS 49/1164/RVD

Full information on the voting for the approval of this standar
...