Aluminium and aluminium alloys - Circle and circle stock for general application - Specifications

This European Standard specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for general applications. It applies to:
— Circles made out of hot or cold rolled circles stock by:
— Blanking: thickness 0,2 mm up to including 12 mm and with a diameter up to 1 000 mm;
— Sawing or shearing: thickness 0,2 mm up to and including 200 mm with a diameter up to 3 500 mm;
— Hot or cold rolled circle stock with a thickness from 0,2 mm up to and including 200 mm and with a width up to 3 500 mm.
It does not apply to slugs for impact extrusions or to circle and circle stock for culinary utensils applications which are dealt with in other European Standards.

Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial für allgemeine Anwendungen - Spezifikationen

Diese Europäische Norm legt die besonderen Anforderungen für Ronden und Rondenvormaterial aus Aluminium-Knetlegierung und Aluminiumlegierungen fest, die für allgemeine Anwendungen eingesetzt werden.
Diese Norm gilt für:
-   Ronden, die aus kalt- bzw. warmgewalztem Rondenvormaterial hergestellt werden;
-   Stanzen (geschlossener Schnitt): mit einer Dicke von 0,2 mm bis 12 mm und einem Durchmesser bis 1 000 mm;
-   Sägen oder schneiden: mit einer Dicke von 0,2 mm bis 200 mm und einem Durchmesser bis 3 500 mm;
-   kalt- bzw. warmgewalztes Rondenvormaterial mit einer Dicke von 0,2 mm bis 200 mm und einer Breite bis 3 500 mm;
Sie gilt weder für Butzen zum Fließpressen, noch für Ronden und Rondenvormaterial für die Herstellung von Küchengeschirr, welche in anderen Europäischen Normen behandelt werden.

Aluminium et alliages d’aluminium - Disques et ébauches pour disques pour applications générales - Spécifications

La présente Norme européenne spécifie les exigences particulières applicables à l'aluminium et aux alliages d'aluminium corroyés sous forme de disques ou d'ébauches pour disques à usage général.
Elle s'applique aux :
-   disques fabriqués à partir d'ébauches pour disques laminées à chaud ou à froid par :
-   poinçonnage : épaisseur comprise entre 0,2 mm et 12 mm inclus, et diamètre inférieur ou égal à 1 000 mm ;
-   sciage ou cisaillage : épaisseur comprise entre 0,2 mm et 200 mm inclus, et diamètre inférieur ou égal à 3 500 mm ;
-   ébauches pour disques laminées à chaud ou à froid, d'épaisseur comprise entre 0,2 mm et 200 mm inclus et de largeur inférieure ou égale à 3 500 mm.
Elle ne s'applique pas aux pions de filage par choc, ni aux disques et ébauches pour disques destinés à la fabrication d'ustensiles culinaires, qui sont traités dans d'autres normes européennes.

Aluminij in aluminijeve zlitine - Rondele in polizdelki za splošno uporabo - Specifikacije

Ta evropski standard določa posamezne zahteve za gneteni aluminij in aluminijeve zlitine v obliki rondel ali polizdelkov za splošno uporabo. Uporablja se za:
– rondele, izdelane iz vroče ali hladno valjanih polizdelkov s:
– finim rezanjem: debelina od 0,2 mm do vključno 12 mm in premer do 1 000 mm,
– žaganjem ali iztiskanjem: debelina od 0,2 mm do vključno 200 mm in premer do 3 500 mm,
– vroče ali hladno valjane polizdelke z debelino od 0,2 mm do vključno 200 mm in premerom do 3 500 mm.
Standard se ne uporablja za kovinske palice za udarno iztiskanje ali za rondele in polizdelke za izdelavo jedilnih pripomočkov in posod, ki so obravnavani v drugih evropskih standardih.

General Information

Status
Withdrawn
Public Enquiry End Date
09-Feb-2014
Publication Date
25-May-2014
Withdrawal Date
10-Apr-2022
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
07-Apr-2022
Due Date
30-Apr-2022
Completion Date
11-Apr-2022

Relations

Buy Standard

Standard
EN 941:2014
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
k FprEN 941:2014
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 941:2014
01-julij-2014
1DGRPHãþD
SIST EN 941:1998
Aluminij in aluminijeve zlitine - Rondele in polizdelki za splošno uporabo -
Specifikacije
Aluminium and aluminium alloys - Circle and circle stock for general application -
Specifications
Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial für allgemeine
Anwendungen - Spezifikationen
Aluminium et alliages d’aluminium - Disques et ébauches pour disques pour applications
générales - Spécifications
Ta slovenski standard je istoveten z: EN 941:2014
ICS:
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 941:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 941:2014

---------------------- Page: 2 ----------------------

SIST EN 941:2014

EUROPEAN STANDARD
EN 941

NORME EUROPÉENNE

EUROPÄISCHE NORM
April 2014
ICS 77.150.10 Supersedes EN 941:1995
English Version
Aluminium and aluminium alloys - Circle and circle stock for the
production of general applications - Specifications
Aluminium et alliages d'aluminium - Disques et ébauches Aluminium und Aluminiumlegierungen - Ronden und
pour disques pour applications générales - Spécifications Rondenvormaterial für allgemeine Anwendungen -
Spezifikationen
This European Standard was approved by CEN on 13 March 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 941:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 941:2014
EN 941:2014 (E)
Contents Page

Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Technical conditions for inspection and delivery .5
4.1 General .5
4.2 Orders or tenders.5
5 Mechanical properties .6
6 Tolerances on dimensions and form .6
6.1 General .6
6.2 Diameter .6
6.3 Thickness .6
6.4 Tolerances on flatness for circles.6

2

---------------------- Page: 4 ----------------------

SIST EN 941:2014
EN 941:2014 (E)
Foreword
This document (EN 941:2014) has been prepared by Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2014 and conflicting national standards shall be withdrawn at
the latest by October 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 941:1995.
With regard the previous version, Clause 2 Normative references was updated; no new alloys were added.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN 941:2014
EN 941:2014 (E)
1 Scope
This European Standard specifies the particular requirements for wrought aluminium and aluminium alloys in
the form of circle or circle stock for general applications.
It applies to:
— Circles made out of hot or cold rolled circles stock by:
— Blanking: thickness 0,2 mm up to including 12 mm and with a diameter up to 1 000 mm;
— Sawing or shearing: thickness 0,2 mm up to and including 200 mm with a diameter up to 3 500 mm;
— Hot or cold rolled circle stock with a thickness from 0,2 mm up to and including 200 mm and with a width
up to 3 500 mm.
It does not apply to slugs for impact extrusions or to circle and circle stock for culinary utensils applications
which are dealt with in other European Standards.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 485-1:2008+A1:2009, Aluminium and aluminium alloys - Sheet, strip, and plate - Part 1: Technical
conditions for inspection and delivery
EN 485-2, Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
EN 485-3:2003, Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions
and form for hot-rolled products
EN 485-4:1993, Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and
dimensions for cold-rolled products
EN 515, Aluminium and aluminium alloys - Wrought products - Temper designations
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
circle
circular flat product obtained by circular sawing or shearing, or by blanking of a flat rolled product with a
uniform thickness over 0,20 mm
4

---------------------- Page: 6 ----------------------

SIST EN 941:2014
EN 941:2014 (E)
3.2
circle stock
flat rolled product of rectangular cross-section with uniform thickness over 0,20 mm, supplied in coils, sheets,
or plates, usually with sheared or sawn edges, and intended to be sawn, sheared or blanked into flat shapes
to be subsequently formed, drawn, etc.
Note 1 to entry: The thickness does not exceed one tenth of the width.
3.3
hot rolled circle and circle stock
circle or circle stock whose final thickness is obtained by hot rolling
3.4
cold ro
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminij in aluminijeve zlitine - Rondele in polizdelki za splošno uporabo - SpecifikacijeAluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial für allgemeine Anwendungen - SpezifikationenAluminium et alliages d’aluminium - Disques et ébauches pour disques pour applications générales - SpécificationsAluminium and aluminium alloys - Circle and circle stock for general application - Specifications77.150.10Aluminijski izdelkiAluminium productsICS:Ta slovenski standard je istoveten z:FprEN 941kSIST FprEN 941:2014en,fr,de01-februar-2014kSIST FprEN 941:2014SLOVENSKI
STANDARD



kSIST FprEN 941:2014



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 941
September 2013 ICS 77.150.10 Will supersede EN 941:1995English Version
Aluminium and aluminium alloys - Circle and circle stock for general application - Specifications
Aluminium et alliages d'aluminium - Disques et ébauches pour disques pour applications générales - Spécifications
Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial für allgemeine Anwendungen - Spezifikationen This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 132.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN 941:2013: EkSIST FprEN 941:2014



FprEN 941:2013 (E) 2 Contents Page Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Technical conditions for inspection and delivery . 5 4.1 General . 5 4.2 Orders or tenders . 5 5 Mechanical properties . 6 6 Tolerances on dimensions and form . 6 6.1 General . 6 6.2 Diameter . 6 6.3 Thickness . 6 6.4 Tolerances on flatness for circles . 6
kSIST FprEN 941:2014



FprEN 941:2013 (E) 3 Foreword This document (FprEN 941:2013) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 941:1995. With regard the previous version, Clause 2 Normative references was updated; no new alloys were added.
kSIST FprEN 941:2014



FprEN 941:2013 (E) 4 1 Scope This European Standard specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for general applications.
It applies to:  Circles made out of hot or cold rolled circles stock by:  Blanking: thickness 0,2 mm up to including 12 mm and with a diameter up to 1 000 mm;  Sawing or shearing: thickness 0,2 mm up to and including 200 mm with a diameter up to 3 500 mm;
 Hot or cold rolled circle stock with a thickness from 0,2 mm up to and including 200 mm and with a width up to 3 500 mm. It does not apply to slugs for impact extrusions or to circle and circle stock for culinary utensils applications which are dealt with in other European Standards. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 485-1, Aluminium and aluminium alloys - Sheet, strip, and plate - Part 1: Technical conditions for inspection and delivery EN 485-2, Aluminium and aluminium alloys – Sheet, strip and plate – Part 2: Mechanical properties
EN 485-3:2003, Aluminium and aluminium alloys – Sheet, strip and plate – Part 3: Tolerances on dimensions and form for hot rolled products
EN 485-4:1993, Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products EN 515, Aluminium and aluminium alloys – Wrought products – Temper designations
3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 circle circular flat product obtained by circular sawing or shearing, or by blanking of a flat rolled product with a uniform thickness over 0,20 mm kSIST FprEN 941:2014



FprEN 941:2013 (E) 5 3.2 circle stock flat rolled product of rectangular cross-section with uniform thickness over 0,20 mm, supplied in coils, sheets, or plates, usually with sheared or sawn edges, and intended to be sawn, sheared or blanked into flat shapes to be subsequently formed, drawn, etc.
Note 1 to entry: The thickness does not exceed one tenth of the width. 3.3 hot rolled circle and circle stock circle or circle stock whose final thickness is obtained by hot rolling 3.4 cold rolled circle and circle stock circle or circle stock whose final thickness is obtained by cold rolling 4 Technical conditions for inspection and delivery 4.1 General All the provisions of EN 485-1 shall apply, except Clause 4 (orders and tenders) which is m
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.